Schascia

There are pieces of the motorbike which in my opinion are timeless iconic, like this 1950s (two-stroke single cylinder) side engine casing which is very simple but has harmonious shapes, I liked the Benelli writing in relief. For many it is certainly simply an "engine crankcase",     I like what I can tell you...

There will be some tests to do before arriving at the final piece, even in this case I will make not many numbered pieces (1/20), also because the mold is delicate, after some time it begins to deteriorate.

If you would like to leave a comment, a suggestion, your personal opinion, please do so, it is always useful.

Finished work installed on wooden base for convenience

Finished models after firing ready to be fixed on a wooden pedestal.

I found some problems in the plaster mold, precisely in the holes used for extraction, the initial repair did not allow the water to absorb well, with the final result that the piece (engine crankcase) was deformed. It seems like a small spot, but it creates a problem in the finished piece. Sanding everything, I redid a plaster cast inside the hole, smoothing everything at the end.

                                   Repair

Together with the Benelli I wanted to reproduce a Mosquito engine crankcase, the size is similar to the first one, honestly I really liked the embossed graphics with the wording made in Italy. The mold is already ready and is in a very long drying phase, it takes a few weeks to drain all the water, almost 4 L. of water.

The mold was made for the Mosquito crankcase, I didn't find any major problems, I used a very dense slip, in 1 day the piece was dry enough to remove it from the mold. At first I thought about making this Mosquito a limited edition too, but I changed my mind.
I attach a couple of photos, you can notice the difference once the piece is dry, but it is normal. Naturally, once the piece is dry with a leather-like consistency, it must be finished completely by hand, the piece must be flat. This is just the first piece of the Mosquito crankcase.

The passion for engines began in 1985 I remember that in the hot summers with hands dirty with gasoline and grease even a can of corned beef was useful, nothing was thrown away. You just had to make some holes, a cable tie and it became a filter for old 50cc scooters. Even today when I see it on the supermarket shelf I can't forget those days...

I have already dismantled and painted old speedometers. This time I had an old empty oil can in my garage that had never been thrown away. With a large hole saw I cut the sheet metal to the exact size of the original. I marked the main speed points with scotch tape and with an acrylic marker I wrote them on the glass, but on the inside. The sheet metal was too new for my tastes, so with a mixture of vinegar, hydrogen peroxide, and salt, I increased the rust that was already there. The result doesn't seem bad to me, but if you want to leave me a comment with your personal opinion, please write!

I didn't finish the outer edge because I didn't feel like it, I realize I could give it a black paint.

La vecchia ruggine è sempre bella...

Soy de la opinión de que incluso una pieza mecánica tiene su encanto.
Esta es la razón por la que quiero reproducir la carcasa lateral de una Gilera Arcore, producida entre 1972 y 75.

In recent years I have become passionate about urban landscapes, both citizens and abandoned works, old Italian restaurants, old service stations, small city shop windows that have now disappeared but have their own hidden charm...

They are small works carried out on cardboard, with markers, pencil, pen, mixed techniques including watercolour, if you wish to leave a comment feel free.

I attach some photographs of my finished work.

I wanted to reproduce the BING because it is one of the carburetors that I like most aesthetically speaking.
I deliberately left the original color of the ceramic, I only gave it a coat of stain to darken the ceramic joints.
Naturally, ceramic can be painted as desired with any color, even enamelled.
If you like the piece and are interested, give me a shout!

The measurement is taken from the original carburettor, once dry the ceramic shrinks by a small percentage compared to the original piece.

Original carburettor

I wanted to do a different test, open the carburettor where the filter and manifold would go, this way the piece is perhaps lighter...

If you wish to leave a comment, your opinion or advice is all welcome.

Janus is an American motorcycle manufacturer, their headquarters are in Indiana, they offer completely handmade  motorcycles  with a unique  and  retro style.  Personalized Janus Motorcycles  2023 annual event poster. The work was done on rigid cardboard with acrylic colours, nothing digital, just old pencil, eraser and colours.

The clay parts are dried for a few days, they are fired, once the clay is cooked the pieces are solid ready to be composed.
They can be left raw or painted
In the last phase, all the pieces must be assembled with a two-component glue, then it will be mounted on a pedestal.

La composición del carburador y todas sus partes está terminada, la última fase es la cocción a 1000°, ya casi llegamos...

Some compositions with newspaper sheets, scissors, a bit of vinyl glue.

Este es mi último trabajo gráfico realizado íntegramente a mano, visto de cerca las imperfecciones no pueden disimular como las marcas del paso del rotulador y lápiz y borrones varios, pero para ser honesto, no me importa mucho...
Cartón rígido 50x60 cm. Técnica con colores Pantone y Uniposca exprimidos y aplicados con brocha en las partes más anchas para una mejor cobertura. La mítica Vespa Primavera ET3.
Espero que os guste, los comentarios siempre son bienvenidos por supuesto.

Preparazione stampo Carburatore BING.

SILODROME.COM

Mi sono crato 4 stampi in gesso dal carburatore originale, due laterali più vaschetta, e uno stampo per i pezzi più piccoli come la pipetta carburante. Una volta uniti i pezzi il tutto va rifinito a mano e svuotato internamente, una volta asciutto il pezzo va cotto in forno ad una temperatura di circa 1000°. Dopo la cottura il manufatto prende consistenza trasformandosi da argilla a Ceramica. Il tutto va rifinito con mordente noce scuro per enfatizzare angoli curve e imperfezioni della ceramica stessa.

Tengo a precisare che è il mio primo lavoro in ceramica.

Estoy trabajando en la realización para una reproducción en cerámica (escala 1:1) de un carburador Moto Guzzi V35 (Dellorto VHB 26 F) Actualmente el artefacto se encuentra en arcilla simple una vez listo se cuece a unos 1000°. El carburador original se desmontó por completo, a partir de las piezas individuales se crearon moldes para la reproducción en serie. La pieza terminada se colocará sobre un pedestal como simple adorno. Mi idea de futuro si todo va bien es crear otros carburadores de otras marcas extranjeras Bing, Mikuni, Teikei etc...

                                         Lavoro grafico per officine Janus Motorcycles

                                            Lavoro grafico per officina Ugly Motors

Publication in the Spanish magazine "Revival of the Machine"